Moulton Water Works Board
EPA’s and Alabama’s records have results for 37 contaminants in its water; 7 were found.
Serves 9,585 people · Surface water · Moulton, AL · Hardness: soft
- Serves
- 9,585 people
- Connections
- 3,195
- Water source
- Surface water
- Based in
- Moulton, AL
- County
- Lawrence
- Owner
- Local government
- Hardness
- Soft
The short answer
None of the results here is above a limit in force today. PFOS is above EPA’s new limit, which takes effect in 2029. No health-based violations on file since 2016.
This is what the records show, not medical advice. Worried about a health effect? Talk to a doctor or your local health department.
What was found
Where these results come from, and when
PFAS and lithium: EPA UCMR 5, samples taken from March 4, 2025 to Feb. 24, 2026.
Haloacetic acids (HAA5), total trihalomethanes (TTHM), arsenic, nitrate, chromium (total) and fluoride: Alabama’s own results, samples taken from Feb. 13, 2020 to Aug. 11, 2026, with EPA’s 2012 to 2019 file for earlier years.
What the lines mean
- Legal limit (MCL):
- Enforceable. The most a utility may deliver.
- EPA’s new limit:
- Final, but not enforced until April 26, 2029. From then on, the most a utility may deliver.
- Health goal (MCLG):
- Not enforceable. The level with no expected risk, with a margin of safety.
- Health benchmark:
- A screening level EPA uses where there is no legal limit or health goal, not an enforceable limit.
PFAS: PFOS and PFBS were found, of the six PFAS in EPA’s 2024 drinking water rule; their results are below. One other PFAS with no federal limit was found, the highest PFBA at 10 ppt: see it below.
Above EPA’s new limit, which takes effect in 2029, 1 result
PFOS
Comes from the source
4.6 ppt
Highest sample, Feb. 24, 2026; found in 1 of 2
The highest sample was 4.6 ppt, above EPA’s new limit of 4.0 ppt, which takes effect in 2029. EPA’s health goal is zero.
How it’s judged
Compliance will be judged on a running annual average, not one sample. No sampling location here has the full set of samples EPA averages to compare with the limit.
What handles it
- NSF/ANSI 53 look for “PFOS Reduction”
- NSF/ANSI 58 look for “Perfluorooctane Sulfonate (PFOS)”
Below EPA’s limits, 5 results
Arsenic has a health goal of zero: the level with no known or expected risk. Any amount found is above it, but the goal isn’t a limit.
- Legal limit (MCL):
- Enforceable. The most a utility may deliver.
- Health benchmark:
- A screening level EPA uses where there is no legal limit or health goal, not an enforceable limit.
Haloacetic acids (HAA5), Legal limit 60 ppb; highest yearly average 34 ppb
Highest yearly average, 2020 to 2026 · 2026 average: 22.2 ppb · Forms or is added in treatment
Averaged by year, the highest was 34 ppb, in 2024, below EPA’s legal limit of 60 ppb. Its highest single sample was 73.5 ppb. In 2026, the latest year on file, its 20 samples averaged below the limit. EPA recorded no violation for haloacetic acids (HAA5) at this utility since 2020.
Earlier, 2012 to 2019
From 2012 to 2019, EPA’s file shows a highest yearly average of 25.6 ppb, in 2017.
What handles it
No certification claim covers this compound yet.
Total trihalomethanes (TTHM), Legal limit 80 ppb; highest yearly average 21.2 ppb
Highest yearly average, 2020 to 2026 · 2026 average: 15.3 ppb · Forms or is added in treatment
Averaged by year, the highest was 21.2 ppb, in 2024, below EPA’s legal limit of 80 ppb. Its highest single sample was 49 ppb. In 2026, the latest year on file, its 20 samples averaged below the limit.
Earlier, 2012 to 2019
From 2012 to 2019, EPA’s file shows a highest yearly average of 32 ppb, in 2013.
What handles it
- NSF/ANSI 53 look for “Trihalomethanes (TTHM) Reduction”
- NSF/ANSI 58 look for “Trihalomethanes (TTHM) Reduction”
Arsenic, Legal limit 10 ppb · health goal zero; highest yearly average 0.89 ppb
Highest yearly average, 2020 to 2025 · 2025: not found · Comes from the source
Averaged by year, the highest was 0.89 ppb, in 2024, below EPA’s legal limit of 10 ppb. Its health goal is zero, so any amount found is above it; the goal isn’t a limit. In 2025, the latest year on file, it wasn’t found in its one sample.
What handles it
- NSF/ANSI 58 look for “Arsenic (Pentavalent)<=50 ppb Reduction”
- NSF/ANSI 53 look for “Arsenic (Pentavalent)<=50 ppb Reduction”
Nitrate, Legal limit 10 ppm; highest 0.65 ppm
Highest sample; found in 5 of 6 · 2025, one sample: 0.61 ppm · Comes from the source
The highest sample, in 2023, was 0.65 ppm, below EPA’s legal limit of 10 ppm. In 2025, the latest year on file, its one sample was below the limit.
Earlier, 2012 to 2019
From 2012 to 2019, EPA’s file shows a highest sample of 0.36 ppm, in 2014.
What handles it
- NSF/ANSI 58 look for “Nitrate/Nitrite Reduction”
- NSF/ANSI 53 look for “Nitrate/Nitrite (30 ppm challenge)”
PFBS, Health benchmark 2,000 ppt; highest 6.7 ppt
Highest sample, Feb. 24, 2026; found in 2 of 2 · Comes from the source
The highest sample was 6.7 ppt, below EPA’s health benchmark of 2,000 ppt. PFBS has no legal limit or health goal of its own.
What handles it
- NSF/ANSI 53 look for “Total PFAS Reduction”
EPA’s 2024 PFAS rule, compound by compoundAll six, found or not, and the Hazard Index, against the rule’s limits.
| PFAS | EPA’s limit | Result |
|---|---|---|
| PFOA | 4.0 ppt | Not foundNot found in any of 2 samples, below 4 ppt |
| PFOS | 4.0 ppt | Above EPA’s new limit (2029)4.6 ppt highest, found in 1 of 2 samples. Details |
| PFHxS | 10 ppt | Not foundNot found in any of 2 samples, below 3 ppt |
| PFNA | 10 ppt | Not foundNot found in any of 2 samples, below 4 ppt |
| HFPO-DA (GenX) | 10 ppt | Not foundNot found in any of 2 samples, below 5 ppt |
| PFBS | Index only | Below EPA’s limits6.7 ppt highest, found in 2 of 2 samples. Details |
| Hazard IndexPFHxS, PFNA, HFPO-DA and PFBS together | 1 | Not worked outNo sampling location has a full set of samples to work it out |
| Results from EPA’s UCMR 5 sampling. “Below” is the lab’s reporting level: a result under it reads as not found, which is not the same as zero. The limits are EPA’s 2024 rule, with compliance due from 2029; EPA has since proposed changes to some of them, explained on each compound’s page. PFBS has no limit of its own and counts only toward the Hazard Index, which adds up the four, each against EPA’s health-based level, from each sampling location’s average, as EPA’s UCMR 5 summary does. It counts only where two or more of the four were found, and is above the limit from 1.5. | ||
Also found, with no federal limit
EPA measured these PFAS to learn how often they occur. None has a legal limit or a health goal yet.
| Compound | Highest sample | Found in | Certification claim |
|---|---|---|---|
| PFBA | 10 ppt | 2 of 2 | None covers it |
30 compounds tested and not foundBelow the reporting level in every sample. Not found is not the same as zero.
From routine monitoring
- Chromium (total)
- Fluoride
- Lead
PFAS and lithium, from EPA’s UCMR 5 sampling
- 11Cl-PF3OUdS
- 4:2 FTS
- 6:2 FTS
- 8:2 FTS
- 9Cl-PF3ONS
- ADONA
- HFPO-DA (GenX)
- Lithium
- NEtFOSAA
- NFDHA
- NMeFOSAA
- PFDA
- PFDoA
- PFEESA
- PFHpA
- PFHpS
- PFHxA
- PFHxS
- PFMBA
- PFMPA
- PFNA
- PFOA
- PFPeA
- PFPeS
- PFTA
- PFTrDA
- PFUnA
What handles it
A certification covers specific claims, not a whole standard. Look for these claims on the certifier’s listing, not the box. Wording varies: “PFOS Reduction” on one listing can read “Perfluorooctane Sulfonate (PFOS)” on another.
- NSF/ANSI 53
Claims: PFOS Reduction, Arsenic (Pentavalent)<=50 ppb Reduction
For: PFOS, Arsenic
Other certifiers’ wording: Perfluorooctane Sulfonate (PFOS)
Other claims that cover it: Total PFAS Reduction; Arsenic (III) (50 ppb influent level)
- NSF/ANSI 58
Claims: Perfluorooctane Sulfonate (PFOS), Arsenic (Pentavalent)<=50 ppb Reduction
For: PFOS, Arsenic
Other claims that cover it: Arsenic (Pentavalent)<=300 ppb Reduction; Arsenic (V) (300 ppb influent level)
At the tap, or for the whole house?
These come with the water itself, so a whole-house system certified for the same claims treats every tap and shower. A filter at the tap treats drinking water for much less. How whole-house systems compare.
Filters with those claims on a certifier’s listing
NSF’s PFAS claims are tested to below 20 ppt. EPA’s limit is 4.0 ppt, and EPA says no certification yet shows a filter reaching its levels.
In the meantime, EPA says reducing the PFAS in your water is still an effective way to limit your exposure, and a filter does that only while it is maintained as its maker says, cartridges replaced on schedule. Showering, bathing and washing dishes in the water are unlikely to significantly increase your risk, EPA says, since little PFAS gets in through the skin.
Disclosure: TapBuff earns a commission if you buy through some links on this page. It does not change which standard or filter we name. As an Amazon Associate, TapBuff earns from qualifying purchases. How TapBuff makes money
Express Water StreamLine Direct Connect System (USC001)
Under-sink carbon
Five years: $527, household of 3, cartridges included
Certified for: PFOS
Brondell Coral UC300 Under Sink Water Filtration System
Under-sink carbon
Five years: $900, household of 3, cartridges included
Certified for: PFOS
A.O. Smith 2-Stage Under Sink Water Filter (AO-US-200)
Under-sink carbon
Five years: $980, household of 3, cartridges included
Certified for: PFOS
2 more filters
Aquasana Claryum 2-Stage (AQ-6200)
Under-sink carbon
Five years: $990, household of 3, cartridges included
Certified for: PFOS
Aquasana Clean Water Machine (AQ-CWM2)
Countertop
Five years: $1,061, household of 3, cartridges included
Certified for: PFOS
Every filter certified for it
Hardness
Soft, 53 mg/L (3.1 grains per gallon), at its one sampling point, 2015 to 2025.
Hardness is calcium and magnesium. EPA sets no limit for it: it shows up as scale on fixtures and in water heaters, and as soap that won’t lather. USGS calls water above 60 mg/L moderately hard, above 120 hard and above 180 very hard.
Disinfectant
Moulton Water Works Board reported disinfecting with chlorine, not chloramine, at its one sampling point, in its 2025 to 2026 sampling for EPA. It also reported chlorine dioxide.
What that means
Chlorine leaves water that sits out for a few days, CDC says. A filter certified for it carries a chlorine claim under NSF/ANSI 42; a shower filter, a free chlorine claim under NSF/ANSI 177. This is what the utility reported for that sampling. Its annual water quality report says what it uses now.
Violations since 2016
No health-based violations on file with EPA since 2016. There are 2 monitoring or reporting violations: a sample missed, late or not reported. EPA’s file runs to 2026 Q3, so a notice your utility sent since then may not be here yet.
What this report can’t tell you
Everything else. Haloacetic acids (HAA5), total trihalomethanes (TTHM), arsenic, nitrate, chromium (total) and fluoride results here are Alabama’s own from 2020 on, with EPA’s national file for 2012 to 2019. Moulton Water Works Board’s own annual report, which it must send you every year, has the contaminants this page does not show.
Your own plumbing. Lead results are the 90th percentile across homes the utility samples. Your home’s service line, solder and fixtures decide yours. A certified lab test is the only way to know.
What it means for your health. This page reports what the records show and EPA’s limits and goals; it is not medical advice. If you are worried about a health effect, talk to a doctor or your local health department.
Anything after the latest data. SDWIS data is from 2026 Q3; UCMR 5 samples are from March 4, 2025 to Feb. 24, 2026; Alabama’s results run from Feb. 13, 2020 to Aug. 11, 2026.
Testing your own tap
What to test for at your tap
- Lead and copper. Both come mostly from a building’s own service line, solder and faucets, so a utility’s numbers can’t tell you yours. Moulton Water Works Board’s latest lead sampling in EPA’s records, 2023 to 2025, had a 90th percentile of 0 ppb across the homes it sampled. The action level is 15 ppb, dropping to 10 ppb in November 2027, and EPA’s health goal for lead is zero. About lead.
- What Moulton Water Works Board’s results flag: PFOS. It is in the water the utility sends out, so a test of your tap mostly confirms it. Include it if you want a number for your own home.
The 3 labs Alabama certifies closest to the area Moulton Water Works Board serves, or a kit by mail
The 3 labs Alabama certifies closest to the area Moulton Water Works Board serves, in a straight line. Call first: certification is test by test, and not every lab takes samples from homeowners.
Pace Analytical National Decatur
Decatur, AL · about 12 miles
Certified for bacteria
Southern Environmental Testing
Decatur, AL · about 13 miles
Certified for bacteria
Limestone County Bacteriological Laboratory
Athens, AL · about 24 miles
Certified for bacteria
Or test by mail
Tap Score sells lab tests as kits you fill at your tap and mail back. The sample goes to Tap Score’s lab, not one near you, so check that Alabama certifies it for the test you want.
Tap Score
- Lead and Copper Water Test, with a pH test strip: $55
- Essential City Water Test, 25 metals, 4 minerals, nitrate, fluoride, hardness and pH: $189
Return shipping included.
Tap Score says each kit ships to “an accredited laboratory” but doesn’t name it, so TapBuff can’t check it against Alabama’s list.
Prices from Tap Score’s own store on Oct. 22, 2026.
What to do now
- Read up on PFOSWhat it does to health, where it comes from, and the certification claim that addresses it.About PFOS
- Get the utility’s own reportMoulton Water Works Board must send you a water quality report every year. It covers contaminants this page does not show.How to read it
- Test your own tap for leadIts latest lead sampling found none at the 90th percentile, but your own service line, solder and fixtures decide the lead at your faucet.Lead in your water: what to do
Sources
- EPA UCMR 5 occurrence data, file of Oct. 15, 2026
- EPA SDWA bulk download (SDWIS federal data), 2026 Q3
- Alabama Department of Environmental Management, Drinking Water Branch, results from Jan. 6, 2020 to Oct. 8, 2026, read Oct. 17, 2026
- EPA Six-Year Review 4 compliance monitoring data, 2012 to 2019, file of Feb. 5, 2024
- Disinfectant: EPA UCMR 5 occurrence data, additional data elements, file of Oct. 15, 2026
- Certified labs: ADEM, certified bacteriological, chemical and PFAS drinking water laboratories, read Oct. 17, 2026; distances from the Census 2020 ZIP code tabulation area gazetteer
- Hardness: Alabama Department of Environmental Management, Drinking Water Branch, results from Feb. 12, 2015 to Nov. 13, 2025, read Oct. 17, 2026
- Limits and goals: each contaminant’s page, with its EPA source.
- How this page is built: methodology.
PWSID AL0000798. Rebuilt from EPA data on Oct. 25, 2026.